Ford f 150 wheel torque specs

After hand-installing your lug nuts, tighten them to your vehicle's torque specs using a torque wrench, a tool designed to measure rotational force. Follow the tightening and loosening pattern shown below. Be careful to tighten to the manufacturer's specifications.

Re: wheel torque specs. by davbell22602 » Wed Nov 16, 2011 8:34 pm. 1/2-20 bolt size is 65-90 ft pounds (F100-250, P100,P350,P3500) 9/16-18 bolt size 125-175 (F350, P350, P400, P3500, P4000) Got this info from my ford factory 67 F series truck manual. jwholgate.The bracket can be torque down to 184 ft-lbs, if the caliper was removed the caliper slide bolts can be torqued to 27 ft-lbs. Now we can move back to the center axle nut and torque it down to 30 ft-lbs, you may need someone to hold down the brake inside the vehicle in order to prevent the rotor from turning.Ford F150 10 (1997-2004) Torque Spec Settings. Bull-Doser, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 10 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.F150 Front Wheel Hub Torque Specs : 129 ft-lbs F150 Front Brake Bracket Torque Specs : 184 ft-lbs ... The front suspension on the 15+ Ford F150's uses a coilover shock suspension. This means that the shock and coil spring are build as the same unit. To remove the old coilover shock you must first unbolt the 2 bolts which hold it down to the ...Jun 17, 2006 · I need the torque specs for a 1995 F150 4x4 front wheel bearings. Any help is appreciated. If you have manual locking hubs. Tighten the nut to 50 ft lbs while you move the hub back and forth to seat the bearings. Back the nut off then retighten to 15 ft. lbs. End play should be 0 to .006 inches. FORD F-10 EXTERIOR DIMENSIONS (INCHES UNLESS OTHERWISE NOTED) 5.5-ft. Styleside 6.5-ft. Styleside 8.0-ft. Styleside SUPERCAB 4x2 4x4 4x2 4x4 4x2 4x4

Going to replace both of my front wheel hubs on a 2000 F-150 7700 4x4 5.4/ auto trans w/ 4 wheel ABS. Need the following specs: 1. Axle nut- the LARGE 35mm nut. 2. The 3 15 or 18mm bolts that bolt the hub to the axle housing. Thanks folks! Reply Like. 04-08-2010, 09:17 PM.Electronic 10-speed automatic features selectable drive modes – normal, tow/haul, snow/wet, eco-select and sport (standard with all-new 2.7-liter EcoBoost®, 3.5-liter EcoBoost and 5.0-liter V8 engines). Second-generation 2.7-liter EcoBoost now has advanced dual port and direct-injection technology.Layout standard Front engine, rear wheel drive Layout optional Front engine, electronically-controlled 4x4 with open differential rear axle ... 2-Speed Torque on Demand (Lariat+) with Flat Tow Mode ENGINES ... SPECIFICATIONS FORD F-150. FORD F-150 TRANSMISSIONS 10-Speed SelectShift® Automatic 10-Speed Modular Hybrid …Mar 12, 2011 · Next, lubricate the front wheel bearings with the correct type of grease and install a new wheel hub grease seal then install the brake disc and hub. Tighten the spindle nut as you turn the brake disc and hub. Torque to 21 ft-lb (28.5 Nm). Loosen the spindle nut by turning counterclockwise 175°. Tighten the spindle nut while rotating the brake ... Lugs: 150 lbFt (204 Nm) 2015 - 2020 Ford F150 - 2016 Front Suspension Torque Specs - I am replacing the front coils and shocks on my 4wd 2016. I have been all over youtube and the web looking for the torque specs. The Haynes youtube video for a 2016 say the Upper Ball Joint should be torque to 45 FT LBS while a Torque Spec …

WHEEL NUT TORQUE SPECIFICATIONS (shown in ft. lbs.) MAKE/MODEL YEARS TORQUE ACURA All Models Except: 2012-90 80 ILX, TSX, ZDX 2013 65 MDX, RDX 2013 85 RL 2012-05 94 TL 2013 85 TL 2012-09 94 ZDX 2012-10 94 AUDI All Models 1997-90 81 All Models Except: 2011-98 89 5000 Series 1988 81 Cabriolet 1998-94 81 RS2 2011 96 Properly torquing the lug nuts on your 2002 Ford F150 is crucial for the safety and performance of your vehicle. Over-tightening or under-tightening the lug nuts can lead to wheel damage, uneven tire wear, and even accidents. Therefore, it is essential to follow the recommended torque specifications to ensure the wheels are securely attached to ...3.5L EcoBoost twin-turbo V6 with electronic 10-speed automatic transmission, electronic Shift-On-The-Fly, Part-Time 4x4 system, column mounted e-Shifter and electronic park brake. 298kW @ 6,000rpm 1. 678Nm @ 3,100rpm 1. Wheels & Tyres. 20-inch six-spoke machined-alloy wheels with Magnetic painted pockets and All-Terrain tyres. Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 111 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle. The rear stabilizer bar on an F150 consists of a large metal bar that connects to both ends of the vehicle. The end connections connect via nuts called link nuts which are torqued down to 75 ft-lbs. The bar is held in place by a set of brackets that connect to the vehicle frame and these bracket bolts also torque down to 75 ft-lbs.

Used ruger mini 14.

The bracket can be torque down to 148 ft-lbs, if the caliper was removed the caliper slide bolts can be torqued to 25 ft-lbs. Now we can move back to the center axle nut and torque it down to 20 ft-lbs, you may need someone to hold down the brake inside the vehicle in order to prevent the rotor from turning.Electronic 10-speed automatic features selectable drive modes – normal, tow/haul, snow/wet, eco-select and sport (standard with all-new 2.7-liter EcoBoost®, 3.5-liter EcoBoost and 5.0-liter V8 engines). Second-generation 2.7-liter EcoBoost now has advanced dual port and direct-injection technology.It is important to note that these values may vary depending on the wheel size, material, and other factors. Always consult your vehicle’s owner’s manual or contact a certified mechanic for the most accurate torque specifications. Below is a table outlining the recommended torque specifications for the 2014 F150:Properly torquing the lug nuts on your 2002 Ford F150 is crucial for the safety and performance of your vehicle. Over-tightening or under-tightening the lug nuts can lead to wheel damage, uneven tire wear, and even accidents. Therefore, it is essential to follow the recommended torque specifications to ensure the wheels are securely attached to ...

2004 - 2008 F150 - Ultimate Torque Spec List - Hey Guys....I along with alot of you have been frustrated by trying for hours to find torque specs for our trucks...If you've found a torque spec for it or if you have a link to a reputable torque spec post it up here and lets try and get a good list of them....Received 84 Likes on 56 Posts. Front wheel hub bolt size and torque? 2014 F150 Lariat 2WD 5.0 with 182k on the clock. While installing a 4” spindle lift in place of my 3” level, I thought it was a good time to replace the front wheel hubs. While installing the last of four wheel hub bolts on the left side, I could not get it to thread.2015 FORD F-150 TECHNICAL SPECIFICATIONS POWERTRAIN/CHASSIS POWERTRAIN 3.5L TI-VCT V6 2.7L EcoBoost® V6 5.0L V8 3.5L EcoBoost V6 Valvetrain Ti-VCT DOHCTi-VCT DOHC Ti-VCT DOHC Block/head Aluminum/aluminum Compacted graphite iron-aluminum/ aluminum Aluminum/aluminum Aluminum/aluminumThe 5.4L starts off with 30 ft-lbs and then an additional 90 degrees then requires you to back them off a full turn. Then you must again torque them to 30 ft-lbs and add 90 degrees then an additional 90 degrees for a total of 180 degrees after the 30 ft-lbs but by going through each bolt with each step.MAKE/MODEL YEARS TORQUE SMART All Models 2010-06 81 All Models 2013-11 110 SUBARU All Models Except: 2005-87 58-72 BRZ 2013 89 Forester, Impreza WRX, WRX STI 2013-11 74 Impreza 2013-12 89 Impreza, Legacy 2010-05 74-89 Impreza, Outback Sport 2011 74 Legacy, Outback, Tribeca w/ other than chromed wheel 2013-11 89 SVX 1997-92 74-89 Tribeca w ...2009 - 2014 Ford F150 - Need Wheel Lug Torque Specs for 2010 Lariat 18" Wheels - Was wondering if anyone has a shop manual that shows what the torque settings are for the 2010 Lariat 18 Chrome Clad aluminum wheel lug nuts. ... its around 150-200. i just step in the bar with my weight until it screams. Reply Like 03-30-2011, 02:24 PM #7 …well correct torque is 100ft lb silver, for if you use torque bars. by Offshore24 » Mon May 02, 2005 7:22 pm. After the recall in 99 Ford was using 100 ft-lbs torque for the aluminum wheels. My lug nuts have the torque requirement on them. by mike424 » Tue May 03, 2005 2:00 am. Ford F150 13 (2015-2020) Torque Spec Settings. Kevauto, CC BY-SA 4.0, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 13 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find. 1995 Ford F150 Lug Nut Torque Specs: Ensuring Safe Wheel Fastening. ... 1995 Ford F150 Lug Nut Torque Specs Introduction. When it comes to maintaining your vehicle, it is crucial to ensure that all components are properly tightened to prevent any accidents or damage. One such component that requires proper torque specifications …

Feb 23, 2024 · In the case of lug nuts, torque specifications are provided to ensure that they are tightened to the appropriate level, neither too loose nor too tight. For a 1997 Ford F150, the lug nut torque specifications are as follows: Lug Nut Size. Torque Specification (lb. ft) Torque Specification (Nm) 1/2″-20. 85-115 lb. ft.

TECHNICAL SPECIFICATIONS. BODY. DRIVETRAIN . ENGINES. TRANSMISSIONS. SUSPENSION. FUEL CAPACITY. SAFETY/CONTROL SYSTEMS. LIGHTING. EXTERIOR DIMENSIONS (INCHES UNLESS OTHERWISE NOTED) 17-inch Silver-Painted Aluminum Wheels. 18-inch Machined-Aluminum Wheels with Flash Gray Pockets and Caribou …Ford F150 11 (2004-2008) Torque Spec Settings. IFCAR, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 11 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.The 2015 Ford Coyote motor is a 5-liter V8 engine that produces 435 peak horsepower and 400 foot-pounds of torque in the 2015 Ford Mustang GT. The version of this engine used in th...Apr 24, 2020 · 2015 - 2020 Ford F150 - Front suspension torque specs - Hey all, I just ordered a Maxtrac drop kit for my 2019 4wd SCREW (3.5), which utilizes replacement spindles (knuckles) up front. Since I'm doing it myself, I need to do some planning regarding torque specs on the following: -Upper ball joint nut -Lower ball joint... Ford F150 12 (2009-2014) Torque Spec Settings. IFCAR, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 12 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.To find torque specs for new Ford vehicles, visit Ford.com, and find the specific vehicle. To find torque specs for older Ford models, browse Edmunds.com, and select a specific For...Ultimate Torque Spec List - Ford Truck Enthusiasts Forums. Ford Truck Enthusiasts Forums. Newer Light Duty Trucks. 2004 - 2008 F150. Ultimate Torque Spec …Common thread diameters used for lug nuts in SAE sizes are 7/16, 1/2, 9/16 and 5/8”. Common metric thread diameters are 12 mm and 14 mm. How to determine thread pitch for your lug nuts. To determine the thread pitch on SAE threads you need to count the number of threads within a one inch long section of the stud. The bracket can be torque down to 145 ft-lbs, if the caliper was removed the caliper slide bolts can be torqued to 25 ft-lbs. Now we can move back to the center axle nut and torque it down to 225 ft-lbs, you may need someone to hold down the brake inside the vehicle in order to prevent the rotor from turning.

Black and decker coffee pot replacement.

Butte mt obituaries 2023.

Actually Ford service manual says to torque inner nut to 50 ft-lbs, while rotating wheel back and forth to seat bearings. Then back nut off 90 degrees. After installing lock ring, install outer lock nut and torque to 50-80 ft-lbs. Hope this helps. This is what I did when i redid my D44 and have had no issues.Forum Jump. 2021+ F150 - Front End Torque Specs. - Hi all - can anyone confirm what the torque specs are for a 2022, F150, 4x4. Looking to install my levelling kit tomorrow and I'm getting mixed results when I search. LCA bolts UCA bolts Sway bar end link - I'm referring to the end link that is located directly behind the ball...The torque specifications for automobile engine cylinder head bolts are located on the Federal-Mogul Motorparts website. The search feature is available on the Specifications Looku...The 4.6L starts off with 30 ft-lbs and then an additional 90 degrees then requires you to back them off a full turn. Then you must again torque them to 30 ft-lbs and add 90 degrees then an additional 90 degrees for a total of 180 degrees after the 30 ft-lbs but by going through each bolt with each step.Search through 2019 Ford Models for specifications, torque specs, and part compatibilities. Home; Cars; Engines; About; Home; Cars; ... F-150 3.5L Turbocharged DOHC (V6)Ford F150 11 (2004-2008) Torque Spec Settings. IFCAR, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 11 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.Electronic 10-speed automatic features selectable drive modes – normal, tow/haul, snow/wet, eco-select and sport (standard with all-new 2.7-liter EcoBoost®, 3.5-liter EcoBoost and 5.0-liter V8 engines). Second-generation 2.7-liter EcoBoost now has advanced dual port and direct-injection technology.Check the number stamped on your lug nut to find its torque specifications. If you don’t see a number, reference the table below to find the lug nut torque specifications for your Ford F-150: F-150 Model Year. Lug Nut Torque. 1975.Ford F150 11 (2004-2008) Torque Spec Settings. IFCAR, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Ford F150 11 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 122 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle.Going to replace both of my front wheel hubs on a 2000 F-150 7700 4x4 5.4/ auto trans w/ 4 wheel ABS. Need the following specs: 1. Axle nut- the LARGE 35mm nut. 2. The 3 15 or 18mm bolts that bolt the hub to the axle housing. Thanks folks! Reply Like. 04-08-2010, 09:17 PM. ….

Advertisement The variety of Android tablets on the market make it difficult to sum up specifications. Android tablets are really just specialized computers. In general, most table...Steering Gear Installation. The steering gear box on the f150 is fastened by a series of bolts that should be torqued down to 65 ft-lbs. The steering wheel bolt is tightened to 30 ft-lbs, and the pinch bolt for the intermediate shaft going between the wheel and the gear box can be torqued to 35 ft-lbs.Advertisement Today's iMac comes in four primary configurations, with a fifth designed specifically for the education market. Let's look first at what they all have in common, then...Oil is especially interesting as it is deemed the cheapest. Cheap is cheap for a reason. Since the start of the year, all investors have been inundated by calls to buy the value st...2012 F-150 XLT 4 by 4 front wheel bearing torque specs I am currently working on my mother-in-law's truck it is a 2012 F-150 XLT 4 x 4 and the front passenger hub is being replaced, I need to know the correct torque specs in inch pounds for the 17 mm spindle nut.Search through 2019 Ford Models for specifications, torque specs, and part compatibilities. Home; Cars; Engines; About; Home; Cars; ... F-150 3.5L Turbocharged DOHC (V6)Apr 24, 2020 · 2015 - 2020 Ford F150 - Front suspension torque specs - Hey all, I just ordered a Maxtrac drop kit for my 2019 4wd SCREW (3.5), which utilizes replacement spindles (knuckles) up front. Since I'm doing it myself, I need to do some planning regarding torque specs on the following: -Upper ball joint nut -Lower ball joint... Message. This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply. Back to Blog. Needing the lug nut torque specs for your F-150? We have put together a quick and easy guide for you to follow to ensure your wheels are tightened to spec. Ford f 150 wheel torque specs, The 5.4L starts off with 30 ft-lbs and then an additional 90 degrees then requires you to back them off a full turn. Then you must again torque them to 30 ft-lbs and add 90 degrees then an additional 90 degrees for a total of 180 degrees after the 30 ft-lbs but by going through each bolt with each step., 3 days ago · Wheel size, PCD, offset, and other specifications such as bolt pattern, thread size (THD), center bore (CB), trim levels for 2022 Ford F-150. Wheel and tire fitment data. Original equipment and alternative options. , 1987 - 1996 F150 & Larger F-Series Trucks - Need a couple torque specs - Im doing front wheel bearings and u loins tomorrow and need the torque spec for the 2 nuts In my manual locking hubs. Is there a proper way to set/ torque them And method/spec for rear ubolts as well please., The bracket can be torque down to 184 ft-lbs, if the caliper was removed the caliper slide bolts can be torqued to 27 ft-lbs. Now we can move back to the center axle nut and torque it down to 30 ft-lbs, you may need someone to hold down the brake inside the vehicle in order to prevent the rotor from turning., Forum Jump. 2021+ F150 - Front End Torque Specs. - Hi all - can anyone confirm what the torque specs are for a 2022, F150, 4x4. Looking to install my levelling kit tomorrow and I'm getting mixed results when I search. LCA bolts UCA bolts Sway bar end link - I'm referring to the end link that is located directly behind the ball..., Steering Gear Installation. The steering gear box on the f150 is fastened by a series of bolts that should be torqued down to 65 ft-lbs. The steering wheel bolt is tightened to 30 ft-lbs, and the pinch bolt for the intermediate shaft going between the wheel and the gear box can be torqued to 35 ft-lbs., Much like the lower control arm this part consists of 3 fasteners, two being bolts in the back of the part and one being a ball joint in the front or closest area of the part. The two bolts in the back will need to be torqued to 111 ft-lbs. The last fastener is the nut that holds the upper ball joint onto the spindle., Fifth Wheel & Gooseneck RV Towing; Toy Hauler Towing; Fifth Wheel & Bumper Pull; Flatbed, Car, Boat, Utility, Horse & Misc. Trailer Towing ... Ford F150 Parts For Sale; Ford F250 Parts For Sale; Ford F350 Parts For Sale; Vendor Directory; ... All torque specs for 351M and 400, print this out. Reply Like, When tightening the bolts back up make sure to torque the top bolt to 66 ft-lbs. The lower bolt on the shock must be tightened to 66 ft-lbs. F150 Rear Shock Upper Bolt Torque Specs : 66 ft-lbs F150 Rear Shock Lower Bolt Torque Specs : 66 ft-lbs, DOHC. Displacement (ci/cc) 302 / 5000. Power / Horsepower. 385 HP @ 5750 rpm. Torque. 387 ft-lb @ 3850 rpm. Engine Oil Capacity. 7 quarts., When I did my clutch last year (351w) I just used the standard torque spec "RFT" (Really F*@#ing tight) lol. I think the real torque spec for the flywheel is right around 50-60 ft. lbs and the pressure plate depends on your clutch size. if i remember correctly 10 inch clutch is 15-20 ft lbs and the 11inch is 20-29 ft lbs or something close to ..., These bolts torque to 150 ft-lbs. Once all 4 bolts are installed you can then reinstall the center wheel nut with some loctite and hand tighten it down for now. Next the brakes need to be reassembled starting with putting the brake rotor back into place and then installing the brake bracket back onto the vehicle., Going to replace both of my front wheel hubs on a 2000 F-150 7700 4x4 5.4/ auto trans w/ 4 wheel ABS. Need the following specs: 1. Axle nut- the LARGE 35mm nut. 2. The 3 15 or 18mm bolts that bolt the hub to the axle housing. Thanks folks! Reply Like. 04-08-2010, 09:17 PM., Steering Gear Installation. The steering gear box on the f150 is fastened by a series of bolts that should be torqued down to 65 ft-lbs. The steering wheel bolt is tightened to 30 ft-lbs, and the pinch bolt for the intermediate shaft going between the wheel and the gear box can be torqued to 35 ft-lbs., The 5.0L Coyote engine block main bearings have 3 sets of fasteners that are used to ensure the bearings stay in place. The first set of fasteners are a series of bolts that screw down vertically into the inwards portion of the bearing caps. These fasteners should be tightened down to 10 ft-lbs and then 48 ft-lbs and finally a 90 degree turn., Steering Gear Installation. The steering gear box on the f150 is fastened by a series of bolts that should be torqued down to 65 ft-lbs. The steering wheel bolt is tightened to 30 ft-lbs, and the pinch bolt for the intermediate shaft going between the wheel and the gear box can be torqued to 35 ft-lbs., Wheel and Tire Tools; Wipers; Wrenches; Dash Cam; Diagnostics. Battery; By Symptom; By Trouble Code; ... Ford Lug Nut Torque Specifications Ford Lug Nut Torque Specifications Here are Ford Lug Nut Torque Specifications. ... 2000 100 ft-lbs F-150 – 14MM STUD 17″BASE / W/14MM NUT 2000 ..., Electronic 10-speed automatic features selectable drive modes – normal, tow/haul, snow/wet, eco-select and sport (standard with all-new 2.7-liter EcoBoost®, 3.5-liter EcoBoost and 5.0-liter V8 engines). Second-generation 2.7-liter EcoBoost now has advanced dual port and direct-injection technology. , The bracket can be torque down to 184 ft-lbs, if the caliper was removed the caliper slide bolts can be torqued to 27 ft-lbs. Now we can move back to the center axle nut and torque it down to 30 ft-lbs, you may need someone to hold down the brake inside the vehicle in order to prevent the rotor from turning., The "Lugnut" thread got me wondering about the torque on aftermarket wheels. In days of yore with custom wheels, 100# of torque is what was recommended, that was with 1/2/20 lugs, which is close to what we use now. I realize with OEM wheels it calls for 150#. Now, I just had custom wheels installed, and the shop torqued nuts to 120#., Ford’s F-150 pickup truck is about as American as a vehicle can get. Ford’s F-150 pickup truck is about as American as a vehicle can get. Not only has the iconic truck been the cou..., The 5.4L starts off with 30 ft-lbs and then an additional 90 degrees then requires you to back them off a full turn. Then you must again torque them to 30 ft-lbs and add 90 degrees then an additional 90 degrees for a total of 180 degrees after the 30 ft-lbs but by going through each bolt with each step., WHEEL NUT TORQUE SPECIFICATIONS (shown in ft. lbs.) MAKE/MODEL YEARS TORQUE ACURA All Models Except: 2012-90 80 ILX, TSX, ZDX 2013 65 MDX, RDX 2013 85 RL 2012-05 94 TL 2013 85 TL 2012-09 94 ZDX 2012-10 94 AUDI All Models 1997-90 81 All Models Except: 2011-98 89 5000 Series 1988 81 Cabriolet 1998-94 81 RS2 2011 96 , 2015 FORD F-150 TECHNICAL SPECIFICATIONS POWERTRAIN/CHASSIS POWERTRAIN 3.5L TI-VCT V6 2.7L EcoBoost® V6 5.0L V8 3.5L EcoBoost V6 Valvetrain Ti-VCT DOHCTi-VCT DOHC Ti-VCT DOHC Block/head Aluminum/aluminum Compacted graphite iron-aluminum/ aluminum Aluminum/aluminum Aluminum/aluminum, 2024 Ford F150 Review, Trims, Specs, Price, New Interior Features, 53 mpg (fwd) / 51 mpg. As you'd expect, the acceleration also sees sizable gains, with the most. Source: www.ford-trucks.com. 2024 Ford F150 Will Receive a MidCycle Refresh, Right on Schedule, Wheel and tire fitment data. Some models lease at 7., If your wife's F150 has different wheels, then it is possible, however all the aluminum Ford wheels with the OEM and/or OEM replacement lug nuts they will take the 150lb/ft. Take note to the larger seat on the lug nuts that Ford provides. That is a lot of surface area. Also, torque is related to the size of the threads., Steering Gear Installation. The steering gear box on the f150 is fastened by a series of bolts that should be torqued down to 65 ft-lbs. The steering wheel bolt is tightened to 30 ft-lbs, and the pinch bolt for the intermediate shaft going between the wheel and the gear box can be torqued to 35 ft-lbs., Once the turbo has been installed in place you can install the oil line and coolant line to the turbo and torque them down to 13 ft-lbs. The oil line to the engine block gets tightened to 31 ft-lbs and the coolant line to the …, WHEEL NUT TORQUE SPECIFICATIONS (shown in ft. lbs.) MAKE/MODEL YEARS TORQUE ACURA All Models Except: 2012-90 80 ILX, TSX, ZDX 2013 65 MDX, RDX 2013 85 RL 2012-05 94 TL 2013 85 TL 2012-09 94 ZDX 2012-10 94 AUDI All Models 1997-90 81 All Models Except: 2011-98 89 5000 Series 1988 81 Cabriolet 1998-94 81 RS2 2011 96 , Straight from the owner's manual. 150 ft. lbs. of torque. Triton 5.4. 3.73 rear ratio. Tow pkge. Bilstein 5100's. HID's: 600k from planethid.com. Nitto Terra Grappler XL's. Future: Ford Racing headers and exhaust, Gyphon, and …, Ford F150 9 (1992-1997) Torque Spec Settings. Below you'll find the tightening torques for the Ford F150 9 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find., 2019 Ford F150 Lug Nut Torque Specs: find the lug nut torque specifications for your 2019 Ford F150 on our chart., FORD: F-150: 4WD / 235/75R15: 1984 - 2000: 100 ft-lbs: F-150 - 14MM STUD: 17"BASE / W/14MM NUT: 2000 - 2008: 150 ft-lbs: F-150 5LUG - 14MM STUD: 16" OPT / HERITAGE: 2004 - 2004: 150 ft-lbs: F-150 - ALL: 18"BASE / ALL CABS: 2008 - 2021: 150 ft-lbs: F-150 SVT - 12MM STUD: 2 DOOR / LIGHTNING: 1999 - 2000: 100 ft-lbs: F-150 SVT - 14MM STUD: LIGHTNG ...